BUKU PINTAR MIGAS INDONESIA Teknologi Proses Kilang Minyak Bumi Halaman 1 dari 3 Kontributor: Adhi Budhiarto BAB I PENDAHULUAN Kilang minyak. 4 Nov Outline Buku Pintar Migas Indonesia sudah dibuat, hanya sayang partisipasi dari anggota untuk membuatnya tidak seperti yang diharapkan. Version: File size: MB. Requirements: Windows (All Versions) / Android / iOS 8+. Languages: Multiple languages. License: Freeware. Date added.
|Published (Last):||28 February 2007|
|PDF File Size:||6.72 Mb|
|ePub File Size:||3.19 Mb|
|Price:||Free* [*Free Regsitration Required]|
Cylinders operating in parallel may iindonesia connected to a common suction and common discharge pulsation device. Rotating discipline should be consulted to determine shut off pressure since it may influence the design pressure of downstream equipment.
If not permanently piped up, the valves shall be fitted with blind flanges. In most cases, pumps are spared. If foaming problems are possible, these separators are able to get buku pintar migas indonesia surface area on the buku pintar migas indonesia for the foam to break down. Where other noise control measures, such as acoustic insulation of acoustic enclosures, are required, they shall not in any case obstruct operation or maintenance personnel activities.
The decision whether water cooling is required is the responsibility of rotating engineer. One stage pump can not develop high pressure except at very high speeds i. An anti surge system will determine the compressor operating point using the pressure, temperature and flow data provided by PT, TT, and FT installed at suction and discharge line that are connected to the anti-surge controller.
Bearing and Seal Losses The polytrophic horse power absorbed by the gas buku pintar migas indonesia phase does not include additional power, which is required for bearing and seal losses. Discharge throttling is buku pintar migas indonesia commonly used as it is inefficient.
Pulsation dampeners can buku pintar migas indonesia liquid-filled, gas-cushioned, or tuned acoustically. A process piping and equipment which forms part of centrifugal or axial compressor system can usually be considered as analogous to the liquid-full pumped systems considerations and the design pressure may be determined in a similar manner. Pulsation can cause significant pressure drop.
Buku Pintar MIGAS INDONESIA – Reservoir Engineering – [PDF Document]
This drum is provided when liquid separation is likely in the waste line. Mechanical seals prevent leakage at the rotating shaft. Reciprocating compressors must be fitted with a safety relief valve on the discharge on each stage, set high enough to prevent its discharge during normal operation.
Seal faces may require cooling and lubrication. To safeguard personnel and equipment against harmful product. For smaller line sizes a flange to flange connection may be possible, provided that removal of the stud bolts is possible in order to turn the spectacle.
Adalah angka perbandingan antara jumlah maksimum hidrokarbon yang dapat buku pintar migas indonesia dengan awal isi hidrokarbon. These enable filter switching without stopping buku pintar migas indonesia pump. At high temperature operation, it should be considered for the possibility of fire and explosion because of the oil vapors present when the handled gas contains oxygen where oxygen is one of the main component of combustion with the oil vapors.
For constant speed drives capacity control can also be achieved by a recycle system.
Two common methods that are used are stuffing boxes and mechanical seals. A surge control valve with equivalent accessories.
Buku Pintar MIGAS INDONESIA – Reservoir Engineering
Simply, the seal purpose is to prevent or buku pintar migas indonesia leakage of liquid out from the pump during operation. Centrifugal Pump consist of a rotor impeller in a casing in which a liquid is given a high velocity head that is largely converted to pressure head by the time the liquid reaches the outlet. DDiimmaannaa hhaarruuss ddiippeerrhhiittuunnggkkaann bbiiaayyaa ppeemmbboorraann, jjuummllaahh ddaann lleettaakk ssuummuurr–ssuummuurr bbaaiikk pprroodduukkssii mmaauuppuunn iinnjjeekkssii, ppeerraallaattaann pprroodduukkssii, hhaarrggaa pontar mmiinnyyaakk ddssbb.
Exception for screw type, the scrubber can be uninstalled where liquid phase may inlet indonsia the compressor section without damaging its compressor.
The valve should be very stable in throttling control. If the required flow is too small for centrifugal compressor or buku pintar migas indonesia the head is so high that an undesirably large number of stages would be necessary that will fall into reciprocating compressor selection. The minimum pressure required at the pump flange is expressed in feet of liquid migaw is called NPSH. Rotary and Screw compressor This type of compressor may be chosen for relatively small flows with relatively large heads and shall be considered only where there is proven experience of acceptable performance of this compressor in the duty concerned and only where there are advantages over a reciprocating compressor.
Hand local temperature control switch can be done by only using TI with set point is based on highest temperature at acceptable value as same as to TSHH to prevent over temperature at downstream equipment related indonesiz process conditioning required or design temperature at its equipment. Light liquid phase and heavy liquid phase should be separated well in gravity settling section caused by difference in density buku pintar migas indonesia the vessel. For reciprocating compressors, adjustable speed electric motor drivers can be buuku for capacity control.
When large volume is available, anti surge system will be not needed to be implemented. The high compressibility of the gas gives absorption of the pressure pulsations. In vertical vessel, where mist extractor is horizontal position, bulk droplet of liquid fall down buku pintar migas indonesia the buku pintar migas indonesia vessel counter current flow direction from gas flow direction.
In addition, compressors generally require lndonesia running-in period during which time and alternative feed gas may be used. In this case, a locked open valve downstream the pressure relief valve is required to enable the pump to be isolated pintzr operation.
buku pintar migas indonesia From migsa figure, a section A first-stage mlgas that the gas comes into the filtercoalescer section buku pintar migas indonesia the inlet nozzle and the T-Feed chamber that distributes the gas flow into two directions, first, the closure end of the vessel section B and the outlet end of the first-stage chamber section C.
The vane pack separates the liquid droplets from the gas at high velocity, draining the liquid into the second-stage drain sump for complete removal. In either case, care should be taken that no other connection exist or will be temporarily made between the vessel and the spectacle blinds that would defeat the isolation of the vessel.
Yes, both of them have same famous name: It contains the inlet nozzle which may be tangential, a diverter baffle, or half open pibtar to take advantage of the inertial effects of centrifugal plntar or an abrupt change of direction to separate the major portion of the liquid from the gas stream.
Provision for piping of stuffing box leakage and other drainage away from the pump should be provided.