9 Dec Part AC metal-enclosed switchgear and controlgear for rated to IEC – the new standard for medium-voltage switchgear. All new medium-voltage switchgear assemblies installed after February 2, must fulfill the new standard IEC/EN 13 Sep IS/IEC High-Voltage Switchgear and Controlgear, Part AC Metal -Enclosed Switchgear and Controlgear for Rated Voltages.

Author: Tadal Dilmaran
Country: Republic of Macedonia
Language: English (Spanish)
Genre: Finance
Published (Last): 9 July 2011
Pages: 91
PDF File Size: 11.25 Mb
ePub File Size: 17.49 Mb
ISBN: 205-7-73495-115-9
Downloads: 87987
Price: Free* [*Free Regsitration Required]
Uploader: Tygora

Temperature rise tests to verify the current carrying capacity with rated normal currents.

IEC – HV Switchgear And Controlgear

Premium Membership Premium membership gives you an access to specialized technical articles and extra premium content electrical guides and software. Degree of protection tests to verify the protection against electric shock and foreign objects. Professional in AutoCAD programming.

At iec 62271 part 200 same time the old IEC standard was pzrt without any transition period. Division of the switchgear panel into four compartments busbar compartment, switching-device iec 62271 part 200, connection compartment and low-voltage compartment ; partitions between the compartments made of sheet steel, front plate made of sheet steel or insulating material.

The assignment is no longer according to the constructional description metalclad, compartmented or 6271 designbut according to operator-related criteria. In the meantime there are tens of thousands of switchgear panels of the primary and secondary distribution level based on this standard in use — certified iec 62271 part 200 to the jec part of the standard and, if required, according to optional tests.

IEC — for four decades this abbreviation was the decisive factor for the type testing of metal-enclosed switchgear. Therefore, with switchgear in metalclad or compartmented design, the busbar in the busbar compartment and 62721 iec 62271 part 200 cable in the connection compartment could remain in operation.

This can lead to a maximum of 25 voltage impulses, whereas the maximum number of permissible disruptive discharges is still two. Peak and short-time iec 62271 part 200 current tests to verify the dynamic and thermal current carrying capacity of the main and earth circuits; the tests are performed with rated peak 622271 current or rated short-circuit iwc current or rated shorttime current or rated short-circuit breaking current.

Are there any published industry codes or standards that cover the inventory tracking, decommissioning, storage, chain of custody, disassembly, and disposal of the waste materials, etc. In contrast to the previous standard, the switching capacity test of both switching devices is no longer carried out as a pure device test. Instead, it is now mandatory to carry out the test in the corresponding switchgear panel.


The ief is copyrighted to EEP and may not iec 62271 part 200 reproduced on other websites. Pressure and strength tests to verify the gas tightness and pressure resistance for gas-fi lled switchgear.

Dielectric test to verify the insulation level of the switchgear tests with rated lightning impulse withstand voltage and rated short-duration power frequency withstand voltage with the specifi ed values depending on the respective rated voltage.

Switchgears are important nodal points in modern power distribution. The passing of the following tests was obligatory in order to identify switchgear as type-tested: Hi, For Auto Reclosures which we plan to install for a 50 Hz system is it ok to accept the parh test reports done in a 60 Hz laboratory???

Significantly stricter changes have also been implemented here. iec 62271 part 200

For the internal arc classifi cation of substations with and without control aisle, the testing of the substation with iec 62271 part 200 switchgear is mandatory in the new IEC standard. According to IECtwo disruptive discharges were permitted in a series of 15 voltage impulses for the test with rated lightning impulse withstand voltage.

Fit for IEC 62271-200?

With a cubicletype design, the incoming cable had to be isolated, but the busbar itself could remain in operation. Above all, the appearance of maintenance- iec 62271 part 200 vacuum circuit-breakers, with operating cycles far exceeding paart normal number, made frequent access to this circuit-breaker no longer of prime importance.

In addition, the five following new criteria must always be completely fulfilled no exceptions are permitted:. This resulted in the first-time use of gas insulation with 622271 important features of iec 62271 part 200 independence, compactness and maintenance-free design. For Prat Reclosures which we plan to install for a 50 Hz system is it ok to accept the type test reports done in a 60 Hz laboratory??? The classification of the substation is only valid in combination with the switchgear used for the test.

High-voltage switchgear and controlgear Part Although the old IEC standard was iec 62271 part 200 helpful, in time it was superseded by the technological progress. Ifc other types of construction that do not meet the above features of the metal-clad or compartmented designs. The classification cannot be transferred to a combination with another switchgear type as each switchgear behaves differently in pat case of an internal arc pressure relief equipment with different cross-sections and pickup pressures, different arcing conditions because of different iec 62271 part 200 geometries.

Correspondingly important is their reliable functioning, a clearly defined switching behavior according to specified parameters as well as the protection of personnel and protection against operational interruptions when an overload occurs.


Nadun Galloluwe Jan 29, Manufacturers and operators can select the criteria which are relevant to them from the following six criteria and have them tested.

Division of the switchgear panel same as for metal-clad switchgear, but with the partitions between the individual compartments made of insulating material.

The same applies to IEC — the new standard for medium-voltage switchgear. In this context, access to the then common minimum-oil-content circuit-breakers for maintenance work without longer operational interruptions was of prime importance because of the limited number of operating cycles. iec 62271 part 200

Four key features are of special note with the new Lart standard: The International Electrotechnical Commission IEC has taken up the task of developing the required specifications, their worldwide standardization and further development.

There is also iec 62271 part 200 possibility of voluntarily certifying switchgear for resistance to internal arc faults and for personal protection.

The switching capacity may get a negative infl uence from the different arrangement of the switchgear with contact arms, moving contacts, conductor bars, etc. The vacuum arc-quenching principle is technologically so superior to other arc-quenching principles that the circuit-breaker can be fixed-mounted again. Therefore, at the end of the nineties, the responsible Iec 62271 part 200 committees decided on the reformulation of the switchgear standard, which finally came into effect as IEC in November However, both technologies — the vacuum arc-quenching principle and gas insulation — were not adequately taken into account in the existing standard.

For this reason, the test duties Ts and Ta from the IEC standard are stipulated for the test of the circuitbreaker inside the switchgear iec 62271 part 200.

Facebook Linkedin Google Plus Twitter. In order to guarantee safe access to the individual switchgear components, e. The energy flow ied iec 62271 part 200 the arc supply, the maximum number of permissible panels with the test in the end panel and the dependency of the ceiling height on the respective panel height have been redefined. Premium Membership Get access to premium electrical guides, technical articles and much more!

Mechanical function test to verify the mechanical functions and interlocks. AC metal-enclosed switchgear and controlgear ice rated voltages above 1 kV and up to and including 52 kV.